Note: If you own a TRAKTOR READY controller, the configuration is done automatically via the Setup Wizard and you may skip to this article. Follow the steps above once again to change the input signal type back to LINE.This article explains how to set up TRAKTOR for the use of an external MIDI controller. The chosen channel will now be set up for MIC signal type. Note: the S4 MK3 will have an EXT button on each Mixer channel. In this example, we are showing the S3, which only has one EXT button, on Channel D. While holding SHIFT, press the EXT button on the corresponding Mixer channel you want to modify.Press and hold SHIFT on either side of the device to access the secondary Deck functions.Plug your S3 or S4 MK3 to a power source via the power supply or USB, then switch it on.In order to switch the input type on your TRAKTOR KONTROL S3 or S4 MK3, follow the steps below: In this manner the channel can operate in TRAKTOR mode, allowing the routing of the external signal into the software for the use of Timecode or Live Input Deck. Make sure the TRAKTOR button below the GAIN knob of the channel in the TRAKTOR KONTROL S8 Mixer section is engaged (lit up).Set the switch above the channel input sockets on the rear panel to either LN (Line) or PH (Phono) depending on the type of device you are connecting.Make sure the TRAKTOR button next to the toggle switch is engaged (lit up).Set the channel toggle switch on the top panel to either PH (Phono) or LN (Line) in correspondance to the external device you connected in step 1.Make sure to connect the output cable (left and right) of your external audio device to either the LINE (CD player, drum machine, etc) or PHONO (turntable) sockets in the INPUT section of the TRAKTOR KONTROL Z2 rear panel.Read more about Phono Gain level settings in the AUDIO 4 / 8 DJ user manual. On a Mac, the Control Panel can be displayed from the drop-down menu below its icon appearing on the top bar of the Desktop. Additionally on the AUDIO 4 / 8 DJ you can adjust the Phono input gain levels in dB from within its Control Panel. Note: Channels C(5,6) and D(7,8) of the AUDIO 8 DJ only offer the LINE input level. Select Phono or Timecode CD / Line from the drop-down menu under channels A(1,2) and B(3,4).Additionally, INPUT CHANNEL D shares its input channel with the microphone ( MIC) input so that a microphone and an external audio source cannot be used at the same time on this channel. The additional THRU / USB switch on INPUT CHANNEL D must be set to USB. Note: The older generation TRAKTOR KONTROL MK1 model offers this switch functionality on the rear panel for INPUT CHANNEL C and INPUT CHANNEL D. Move the switch to either LINE or PHONO next to the INPUT CHANNEL B or INPUT CHANNEL A on the rear panel of the TRAKTOR KONTROL S4 hardware. Read about the Direct Thru and stand-alone use of the TRAKTOR AUDIO 6 / 10 in this article. Additionally, if you wish to save the Input Sens configuration for future use, perform these changes under the Startup tab. Note: Make sure that the Direct Thru option of the input channels is disabled. In the Channel Setup menu, use the radio buttons under Input Sens for each channel to switch between Phono and Line level.Click on Settings in the Phono / Line section to open the Control Panel.Note: To learn about the use of external audio sources as Live Input signal in TRAKTOR, please consult this video.īefore proceeding, make sure that your TRAKTOR audio interface or controller has been connected and recognized by your system.Ĭlick on the name of your device to learn how to switch the level of its input channels: The PHONO signal level is required when connecting a turntable as part of a TRAKTOR Scratch Timecode vinyl setup or as an external audio source (Live Input) from a vinyl record playing. This article explains how to switch between the LINE and PHONO levels on the input channels of TRAKTOR audio interfaces equipped with this feature.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |